- Microchip MCP96L00
- Supports K Type Thermocouples
- 0.0625°C Resolution
- Internal Cold-Junction Temperature Compensation
- Programable Rising or Falling Temperature Alerts for Hot and Cold Junctions
- Low Power Consumption
-
-
- Texas Instruments HDC1080
- Relative Humidity Accuracy ±2% (Typ)
- Temperature Accuracy ±0.2°C (Typ)
- Excellent Stability at High Humidity
- 14-bit Measurement Resolution
- 100nA Sleep Current
- Average Supply Current:
- 710nA @ 1sps, 11-bit RH Measurement
- 3μA @ 1sps, 11-bit RH and Temperature Measurement
-
- Displays the Status of Each Data and Power Connection
- Signals Pass Through Visualizer with No Losses
- Great for Troubleshooting
-
- Adapts Trēo to Raspberry Pi Boards
- 8 Trēo™ Connectors
- 4 I2C
- 3 SPI
- 3 GPIO
- 1 UART
- 1 SDIO
- RoHS Compliant
-
- 420 Tie-Point Bread Board Layout
- 2 Trēo™ Connectors
- Pull-up Resistors Pre-installed
- RoHS Compliant
- Add custom circuitry to the Trēo™ system
-
- TCA9534A GPIO Expander
- 16 Key Input Pad
- I2C Interface
- Interrupt Generation
-
- mircoSD Card
- Connects to SPI Bus
- Utilizes Native SPI SD Libraries
- E.g. Arduino SD Library
-
- Texas Instruments OPT3002
- Wide Optical Spectrum: 300 nm to 1000 nm
- Automatic Full-Scale Setting Feature Simplifies Software and Configuration
- Measurement Levels: 1.2 nW/cm2 to 10 mW/cm2
- 23-Bit Effective Dynamic Range with Automatic Gain Ranging
- 12 Binary-Weighted, Full-Scale Range Settings: <0.2% (typ) Matching Between Ranges
-
- Creates Two I2C Connections From One
- Creates Two GPIO Plugs with GPIO0 From One with GPIO0 & GPIO1
-
- Texas instruments TCA9534A
- 5-V Tolerant I/O Ports
- Three Hardware Address Pins Allow up to Eight Devices on the I2C bus
- Pin-Change HW Interrupt
-
- Adapts Trēo to All Arduino Uno Style Boards
- Arduino Boards
- STM32 Nucleo Boards
- Compatible with 5V or 3.3V Boards
- 9 Trēo™ Connectors
- 6 I2C
- 3 SPI
- 3 GPIO
- 1 UART
- RoHS Compliant
- Adapts Trēo to All Arduino Uno Style Boards
-
- 3-Axis Accelerometer
- FSR of ±2g, ±4g, ±8g, or ±16g
- 3-Axis Gyroscope
- FSR of ±250dps, ±500 dps, ±1000dps, or ±2000dps
- 3-Axis Compass
- FSR of ±4900µT
- On-Chip 16-bit ADCs and Programmable Filters
- Digital-output temperature sensor
- 3-Axis Accelerometer
-
- Holtek HT16k33
- 8 Digit Numerical Display (Red)
- 16-Step Dimming
-
- Allegro ACS70331
- 5mA Precision
- High-Sensitivity Sensing Up to 5A (AC or DC)
- 1MHz Bandwidth (Response <550ns)
- 1mΩ Resistance Results in Low Losses
-
- On Semiconductor CAT25512
- 128-byte Page Write Buffer
- Additional Identification Page with Permanent Write Protection
- Self-timed Write Cycle
- Hardware and Software Protection
- Block Write Protection
- Protect ¼, ½, or Full EEPROM Array
- Low Power CMOS Technology
- 4,000,000 Program/Erase Cycles
- 200 Year Data Retention
-
- 0 - 4.096V Range
- 12-Bit Resolution
- 4 Single-Ended Channels or 2 Fully Differential Channels
- Internal Voltage Reference
- 5MHz Bandwidth (-3dB)
-
- Holtek HT16k33
- 4 Digit Numerical Display (Red)
- 16-Step Dimming
-
- ±4/±8/±12/±16 gauss selectable magnetic full scales
- 16-bit data output
- Continuous and single-conversion modes
- Interrupt generator
- Self-test
- Power-down & low-power modes
-
- 3-Axis X,Y,Z
- 10-bit Resolution
- ±16g Range
- Single/Double Tap Detection
- Free-Fall Detection
- 10,000g Shock Survival
-
- AVIA HX711
- 2 Input Channels
- Low Noise PGA
- Selectable Gain of 32, 64, and 128
- 80 Samples Per Second
-
- Allegro ACS711
- 11mA Precision
- High-Sensitivity Sensing Up to 15.5A
- 100kHz Bandwidth (Response <550ns)
- 6mΩ Resistance Results in Low Losses
-
- 0 - 40V Range
- 12-Bit Resolution
- 4 Single-Ended Channels or 2 Fully Differential Channels
- Internal Voltage Reference
- 5MHz Bandwidth (-3dB)
-
STM32 Nucleo-144 development board with STM32F767ZI MCU is compatible with the Trēo system, supports Arduino, ST Zio, and morpho connectivity
